BMW 7 Series (F01/F02) 2008-2015 Service Manual / Rear Axle
BMW 7 Series: Rear Axle
Tightening Torques
ANTI-ROLL BAR
TIGHTENING TORQUE SPECIFICATION - ANTI-ROLL BAR
.png)
HANDLEBARS AND STRUTS
TIGHTENING TORQUE SPECIFICATION - HANDLEBARS AND STRUTS
.png)
.png)
.png)
INTEGRAL ACTIVE STEERING
TIGHTENING TORQUE SPECIFICATION - INTEGRAL ACTIVE STEERING
.png)
.png)
REAR AXLE SUSPENSION
TIGHTENING TORQUE SPECIFICATION - REAR AXLE SUSPENSION
.png)
REAR AXLE FINAL DRIVE SUSPENSION
TIGHTENING TORQUE SPECIFICATION - REAR AXLE FINAL DRIVE SUSPENSION
.png)
.png)
REAR AXLE GEARBOX HOUSING WITH LID
TIGHTENING TORQUE SPECIFICATION - REAR AXLE GEARBOX HOUSING WITH LID
.png)
SHOCK ABSORBERS
TIGHTENING TORQUE SPECIFICATION - SHOCK ABSORBERS
.png)
.png)
WHEEL BEARINGS
TIGHTENING TORQUE SPECIFICATION - WHEEL BEARINGS
.png)
- Operating Fluids
- General
- Danger Of Poisoning If Oil Is Ingested/Absorbed Through The Skin
- Lifting Vehicle Using A Vehicle Hoist
- Rear Axle Layout
- Repair Solution For Straight Shank/Hexagon Rivet Nut
- Final Drive
- Checking/Topping Up Oil Level In Rear Axle Final Drive
- Replacing Shaft Seal For Drive Flange Left Or Right
- Final Drive With Cover
- Checking/Topping Up Oil Level In Rear Differential
- Replacing Cover Gasket On Rear Differential (205AL/225AL) At Rear
- Replacing Shaft Seal For Drive Flange On Rear Differential (Inserted Propeller Shaft)
- Final Drive Mounting
- Output Shafts
- Rear Sub-Frame
- Lowering/Raising Rear Axle Support
- Removing And Installing Complete Rear Axle Support
- Replacing Rear Axle Support
- Control Arms And Struts
- Removing And Installing/Replacing A Steering Stub/Wheel Carrier
- Removing And Installing/Replacing Left Or Right Antiroll Bar Link/Integral Link
- Removing And Installing/replacing Left Or Right Tank Cover
- Removing And Installing/Replacing Lower Left Or Right Cover (Wheel Arch)
- Replacing An Upper Wishbone
- Axle Mounting
- Active Rear Axle Kinematics
- Wheel Bearings
- Detaching Wheel Bearing Inner Ring From Drive Flange (Drive Flange Removed)
- Replacing Drive Flange On Left/Right Rear Axle Shaft
- Shock Absorber
- Stabilizer Bar
- Special Tools
READ NEXT:
Operating Fluids
1.0 GENERAL INFORMATION ON FINAL DRIVE OIL
Final Drive oil or hypoid gear lubricant must conform with the following
requirements because of the high
loads which occur on the profiles of the hypoid ge
Danger Of Poisoning If Oil Is Ingested/Absorbed Through The Skin
Danger of poisoning!
Ingesting oil or absorbing through the skin may cause poisoning!
Possible symptoms are:
Headaches
Dizziness
Stomach aches
Vomiting
Diarrhoea
Cramps/fits
Unconsciousness
P
SEE MORE:
Removing And Installing/Replacing Inlet And Exhaust Adjustment
Units On Right Side (N63)
Notes
IMPORTANT: When the engine is shut down, the inlet and exhaust camshaft
adjuster is
normally locked in its initial position.
The situation may arise in some individual cases where this initial position is
not reached and the camshaft can continue to be rotated in the adjustment
range of the
Removing And Installing/Replacing Engine Oil Cooler (N54, N63)
Necessary preliminary tasks
Remove front right WHEEL ARCH TRIM.
WARNING: Danger of scalding!
Only perform this work after engine has cooled down.
IMPORTANT: Wear protective goggles and gloves.
IMPORTANT: Adhere to conditions of absolute cleanliness when working on
the engine oil
circuit.
When r
© 2019-2026 Copyright www.bmw7g11.com
