BMW 7 Series (F01/F02) 2008-2015 Service Manual / General Electrical System
BMW 7 Series: General Electrical System
- Troubleshooting
- Battery Replacement Information
- Diagnosis For Condition Based Service
- General Information On Intelligent Battery Senor (IBS)
- Instructions For Opening Contacts And Locks Of Different Plug Contact Systems
- Notes On Handling Optical Fibres
- Repairing Airbag Cables
- Wiring Harness
- Installing Repair Cable For Left Side View Camera
- Installing Repair Cable For Reversing Camera
- Notes On Handling Wiring Harnesses And Cables
- Auxiliary Cable
- General Information On Intelligent Battery Sensor (IBS)
- Replacing Battery Negative Lead
- Replacing Wiring Harness In Left Or Right Front Door
- Plug Connection, Terminal, Fuse Box
- Butt Connector For Repairing A Plug Connection
- Circular Connector, 7-Pin, 8-Pin, System D2.5
- Inline Connectors, 15-Pin, System D2.5
- In-Line Plugs, 24-Pin, Hybrid System MQS/MPQ
- Connector Housing, LCC Contact (Load Current Contact)
- Crimping Micro Power Quadlock Contacts (MPQ)
- Crimping Optical Fibres
- Crimping Stop Parts
- Instructions For Opening Contacts And Locks Of Different Plug Contact Systems
- Notes On Handling Optical Fibres
- Removing And Installing/Renewing USB Interface Connecting Socket
- Replacing Power Distribution Box (Luggage Compartment)
- Distribution Box, Power Support Points
- Battery
- (Safety) Information On AGM Battery
- Battery Replacement Information
- Disconnecting And Connecting Negative Battery Cable
- Battery/Vapor Separator
- Switch
- Carrying Out Steering Angle Sensor Adjustment
- Removing And Installing (Replacing) Front Controller
- Removing And Installing Operating Unit For Additional Seat Functions
- Removing And Installing Steering Column Switch Cluster
- Removing And Installing/Replacing Both Multifunction Steering Wheel Switches
- Replacing Audio Unit
- Replacing Operating Unit For Seat Adjustment
- Replacing Roof Switch Cluster (Roof Function Center)
- Horn
- Insert Holder
- Control Units, Modules
- Initializing Rain/Light (Solar) Sensor
- Removing And Installing (Replacing) Smart Opener Bottom Sensor Line (Non-Contact Rear Lid Opening)
- Removing And Installing (Replacing) Control Unit For Automatic Operation Of Tailgate System
- Removing And Installing Or Replacing Junction Box Electronics
- Removing And Installing/Replacing Control Unit For Active Front Steering
- Removing And Installing/Replacing Control Unit/Module For Left Or Right Seat Adjustment (Rear Comfort Seat)
- Replacing Audio Unit
- Windscreen Wipers
- Checking Contact Angle Of Windscreen Wiper Arms On Front Windscreen
- Removing And Installing Or Replacing Console For Windscreen Washer System Complete With Motor
- Headlight Washer System
- Window Washer System
READ NEXT:
Battery Replacement Information
A vehicle battery is constructed for the installation location and the
individual power requirements of the
particular vehicle. These individual power requirements depend on the
motorization and dif
Diagnosis For Condition Based Service
NOTE: Red symbol for pre-delivery check
The vehicle is coded at the end of the assembly line so that the red symbol
for the pre-delivery check is shown
in the Next Service display (same symbol as veh
SEE MORE:
Removing And Installing/Replacing Center Fresh Air Grille
Necessary preliminary work
F01, F02, F03, F12, F13:
Remove DECORATIVE STRIP ON DASHBOARD IN MIDDLE
F07, F10, F11, F18:
Remove decorative strip on dashboard on right
IMPORTANT: Proceed with care so as to avoid damaging the fresh air grille.
NOTE: Picture for example purposes only!
Replacement
R
Replacing Rear Cross Member On Luggage Compartment Floor (Tail
Panel Removed)
Read contents of BODY, GENERAL.
STRIP DOWN VEHICLE
Observe new procedure for bonding and riveting (REPAIR STAGE 2).
Following new body parts are required:
End of luggage compartment floor
Following consumables are required:
MATERIAL CHART
Fig. 349: Identifying End Of Luggage Compartment Floor
© 2019-2026 Copyright www.bmw7g11.com
