BMW 7 Series: Replacing Actuator Drive For Left Footwell Flap
Necessary preliminary tasks
- Remove INSTRUMENT PANEL TRIM
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATING AND AIR-CONDITIONING UNIT
Release screws (1) and remove grounding cable.
Installation note: Replace screws (1).
Take off holder (2).
.png)
Fig. 53: Identifying Holder And Screws
Unclip connector piece (1) and slide downwards.
Installation note: Latching of connector piece (1) must be felt.
.png)
Fig. 54: Unclipping Connector Piece
Release screws (1).
Feed out left footwell air outlet duct (2).
.png)
Fig. 55: Identifying Left Footwell Air Outlet Duct And Screws
Release screws (1).
Remove servomotor (2) and unlock and disconnect plug connection (3).
.png)
Fig. 56: Identifying Servomotor, Plug Connection And Screws
Replacement:
Servomotors must be readdressed in the event of replacement! Addressing can only be carried out with the BMW diagnosis system.
Service functions:
- Body
- Heating and air conditioning function
- Flap motors
- Readdress flap motors
REPLACING ACTUATOR DRIVE FOR LEFT REAR CABIN BLENDING FLAP
Necessary preliminary tasks
- Remove INSTRUMENT PANEL TRIM
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1) and remove grounding cable.
Installation:
Replace screws (1).
Take off holder (2).
.png)
Fig. 57: Identifying Holder And Screws
Unclip connector piece (1) and slide downwards.
Installation: Latching of connector piece (1) must be felt.
.png)
Fig. 58: Unclipping Connector Piece
Release screws (1).
Feed out air outlet duct (2) Installation: Ensure correct cable routing air outlet duct (2).
.png)
Fig. 59: Identifying Air Outlet Duct And Screws
Release screws (1).
Remove servomotor (2) and unlock and disconnect plug connection (3).
.png)
Fig. 60: Identifying Servomotor, Plug Connection And Screws
Replacement:
Servomotors must be re-addressed in the event of replacement! Addressing can only be carried out with the BMW diagnosis system.
Service functions:
- Body
- Heating and A/C function
- Flap motors
- Re-address flap motors
READ NEXT:
Replacing Actuator Drive For Left Rear Cabin Footwell Flap (High
A/C System)
Necessary preliminary tasks
Remove INSTRUMENT PANEL TRIM
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1) and remove grounding cable.
Installatio
Replacing Actuator Drive For Right Footwell Flap
Necessary preliminary tasks
Remove INSTRUMENT PANEL TRIM
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1).
Take off holder (2).
Fig. 73: Identif
Replacing Actuator Drive For Right Rear Cabin Footwell Flap (High
A/C System)
Necessary preliminary tasks
Remove trim for instrument panel, bottom right.
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1).
Installation:
Repla
SEE MORE:
Reference
Numerous subjects pertaining to the BMW 7 Series' mechanical, electrical, and performance features are covered in this chapter.
Engine specs are one of the main topics this chapter covers. It contains information on the fuel type, emission regulations, torque, power output, displacement, and engine
Replacing Luggage Compartment Floor, Left Section (Tail Panel Or
Side Wall Removed)
Read contents of BODY, GENERAL.
STRIP DOWN VEHICLE
NOTE: Observe new procedure for bonding and riveting (REPAIR STAGE 2).
Following new body parts are required:
Luggage compartment floor, left Following CONSUMABLES are required:
MATERIAL CHART
Fig. 170: Identifying Left Luggage Compartment Floo
