BMW 7 Series: Replacing Actuator Drive For Right Footwell Flap
Necessary preliminary tasks
- Remove INSTRUMENT PANEL TRIM
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1).
Take off holder (2).
.png)
Fig. 73: Identifying Holder And Screws
Unclip connector piece (1) and slide downwards.
Latching of connector piece (1) must be felt.
.png)
Fig. 74: Unclipping Connector Piece
Release screws (1).
Feed out right footwell air outlet duct (2).
If necessary, disconnect plug connections at actuators.
.png)
Fig. 75: Identifying Right Footwell Air Outlet Duct And Screws
Release screws (1).
Remove servomotor (2) and unlock and disconnect plug connection (3).
.png)
Fig. 76: Identifying Servomotor, Plug Connection And Screws
Replacement
Servomotors must be re-addressed in the event of replacement! Addressing can only be carried out with the BMW diagnosis system.
Service functions:
- Body
- Heating and A/C function
- Flap motors
- Re-address flap motors
REPLACING ACTUATOR DRIVE FOR RIGHT REAR CABIN AIR BLENDING FLAP
Necessary preliminary tasks
- Remove INSTRUMENT PANEL TRIM
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1).
Installation:
Replace screws.
Take off holder (2).
.png)
Fig. 77: Identifying Holder And Screws
Unclip connector piece (1) and slide downwards.
Installation:
Latching of connector piece (1) must be felt.
.png)
Fig. 78: Unclipping Connector Piece
Release screws (1).
Remove air vent duct (2).
Installation:
Ensure cable routing along air vent duct (2) is correct
.png)
Fig. 79: Identifying Air Vent Duct And Screws
Release screws (1).
Remove actuator drive (2) and unlock and disconnect associated plug connection.
.png)
Fig. 80: Identifying Actuator Drive And Screws
Replacement
Servomotors must be re-addressed in the event of replacement! Addressing can only be carried out with the BMW diagnosis system.
Service functions:
- Body
- Heating and A/C function
- Flap motors
- Re-address flap motors
READ NEXT:
Replacing Actuator Drive For Right Rear Cabin Footwell Flap (High
A/C System)
Necessary preliminary tasks
Remove trim for instrument panel, bottom right.
Position of actuator drive:
OVERVIEW OF ACTUATOR DRIVES ON HEATER/AIR CONDITIONER
Release screws (1).
Installation:
Repla
Replacing Controller For Heating And A/C System Fan
Necessary preliminary tasks
Remove FAN HOUSING FOR HEATER/AIR CONDITIONER
Unlock plug connections (1) and disconnect.
Release screws (3).
Remove controller (2) towards top.
Fig. 89: Identifying
Replacing Interior Temperature Sensor Blower (A/C Control Panel)
Necessary preliminary work
Remove RADIO AND IHKA CONTROLS
Release screws (1).
Tightening torque 61 31 2AZ.
NOTE: Use special tool 00 9 450 to tighten screws.
Remove fan (2) from IHKA controls (3).
SEE MORE:
System Components
Control Unit
The Car Access System is located above the steering column on the right-hand
side.
For the Comfort Access function, the Car Access System controls the transmitting
antennas for the vehicle
The outside door handle electronics are read by the Car Access System.
Fig. 6: Installation Lo
Vehicle key- Trunk lid
General information
To avoid locking the vehicle key in the vehicle,
do not place the vehicle key in the cargo area.
You can set up if the doors will be unlocked
when the trunk lid is opened with the vehicle key.
Safety information
Warning
Body parts can be jammed when operating the
trunk lid. The
