BMW 7 Owners & Service Manuals
BMW 7 Series (F01/F02) 2008-2015 Service Manual / Propeller Shaft / Propeller Shaft Assembly / Removing And Installing/Replacing Front Centering Mount For Propeller Shaft

BMW 7 Series: Removing And Installing/Replacing Front Centering Mount For Propeller Shaft

Necessary preliminary work

  • Remove PROPELLER SHAFT.

Completely fill centering bore hole (1) with viscous grease.

Drive special tool 11 1 310 with a plastic hammer into centering bore hole.

The centering bearing (1) is forced out of the propeller shaft by the pressure on the grease filling.

If necessary, top up grease repeatedly.

NOTE: To drive out the bearing, you can also fill the centering bore hole with water instead of grease.

Propeller Shaft, General and Assembly
Fig. 19: Driving Special Tool (111310) With A Plastic Hammer Into Centering Hole

Installation note: Remove grease or water from mount bore.

Drive in centering mount (1) with special tools 11 2 030 and 00 5 500 into propeller shaft (observe protrusion).

Grease centering mount.

  • Grease: See DRIVESHAFT - OPERATING FLUIDS.

Propeller Shaft, General and Assembly
Fig. 20: Installing Centering Mount Using Special Tools (11 2 030 And 00 5 500)

Installation note:

Observe protrusion A = 4+2 mm of centering (1).

Propeller Shaft, General and Assembly
Fig. 21: Observing Protrusion Of Centering

REMOVING AND INSTALLING/REPLACING REAR CENTERING MOUNT FOR PROPELLER SHAFT

Necessary preliminary work

  • Remove PROPELLER SHAFT.

Completely fill centering bore hole (1) with viscous grease.

Drive special tool 11 1 310 with a plastic hammer into centering bore hole.

The centering bearing (1) is forced out of the propeller shaft by the pressure on the grease filling.

If necessary, top up grease repeatedly.

NOTE: To drive out the bearing, you can also fill the centering bore hole with water instead of grease.

Propeller Shaft, General and Assembly
Fig. 22: Driving Special Tool (111310) With A Plastic Hammer Into Centering Hole

Installation note: Grease or water must be removed from the bearing bore.

Drive in centering mount (1) with special tools 11 2 030 and 00 5 500 into propeller shaft (observe protrusion).

IMPORTANT: Plastic centering mount must not be greased.

Propeller Shaft, General and Assembly
Fig. 23: Installing Centering Mount Using Special Tool 11 2 030 And 5 500

Installation note: Observe protrusion A = 4+2 mm of centering (1).

Propeller Shaft, General and Assembly
Fig. 24: Observing Protrusion Of Centering

    READ NEXT:

     Replacing Center Mount Gaiter

    Necessary preliminary work Remove PROPELLER SHAFT. NOTE: The propeller shaft is balanced. The front and rear propeller shafts must be reassembled in the same position. Detach gaiter (1) from groo

     Center Console Assembly

     Replacing Center Mount Gaiter

    Necessary preliminary work Remove PROPELLER SHAFT. NOTE: The propeller shaft is balanced. The front and rear propeller shafts must be reassembled in the same position. Detach gaiter (1) from groo

    SEE MORE:

     Removing And Installing/Replacing Both Solenoid Valves On Left Side (N63)

    IMPORTANT: Always check that the solenoid valves are clean during removal and installation. Possible malfunctions if valves are contaminated: Irregular operation OBD incorrect entry Poor exhaust gas values Low engine performance IMPORTANT: Risk of damage! Do not clean solenoid valves with co

     Replace Roof Outer Skin

    Read contents of BODY, GENERAL. STRIP DOWN VEHICLE NOTE: Observe new procedure for bonding and riveting (REPAIR STAGE 2). Following parts are required: Roof outer skin Additional required parts (not pictured): SOUND INSULATION CHART Following consumables are required: MATERIAL CHART Fig. 271:

    © 2019-2026 Copyright www.bmw7g11.com