BMW 7 Owners & Service Manuals
BMW 7 Series (F01/F02) 2008-2015 Service Manual / Body / Stamping Vehicle Identification Number (Needle Stamping Unit)

BMW 7 Series: Stamping Vehicle Identification Number (Needle Stamping Unit)

Read and comply with GENERAL INFORMATION.

The needle stamping system 360 - VRM - BMW is required to stamp the vehicle identification number.

Order number: 81 43 2 155 736

  • Sourcing reference:
    BMW Workshop Equipment Catalogue.

Body
Fig. 69: Identifying Display, Mains Adapter, Needle Stamping Unit, Connecting Cable And Power Cable

The needle stamping system 360 tool set comprises:

  1. Display
  2. Mains adapter
  3. Needle stamping unit
  4. Connecting cable
  5. Power cable
  6. Compressed-air hose

NOTE: A compressed-air connection is also required.

  • Operating pressure approx. 4 bar
  • Use only dried, oil-free air

Procedure for additional vehicle identification number

  • Cross through original vehicle identification number.

Body
Fig. 70: Identifying Vehicle Identification Number Position

Remove ENGINE COMPARTMENT LID SEAL LOCATOR

(1) = Original vehicle identification number (line 1).

Mark position lines (2) in accordance with specified dimensions/measurements.

Measurement a = 12 mm

Measurement b = 10 mm

Display input:

  • Select Layout 5 with arrow button.
  • Enter vehicle identification number with F10.
  • Press "ENTER" button.

NOTE: With Layout 5 the vehicle identification number (line 1) is crossed through.

Body
Fig. 71: Identifying Display

IMPORTANT: Perform stamping operation with position lines in advance on a test sheet.

Body
Fig. 72: Identifying Suction Feet Of Needle Stamping Unit Moving Position

Move suction feet of needle stamping unit to positions (1) and (2) shown.

  • First adjust position (1)
  • Then adjust position (2)

NOTE: Make sure the unit is resting securely in position. If necessary, adjust the height and position of the suction feet.

Press pushbutton (1) for vacuum pressure.

Then start stamping operation with pushbutton (2).

IMPORTANT: After completing the stamping operation, do not alter the position of the unit.

Do not switch off vacuum pressure.

Body
Fig. 73: Stamping Vehicle Identification Number

Stamping second vehicle identification number

Display input:

  • Select Layout 2 with arrow button.
  • Press "ENTER" button.

NOTE: With Layout 2 the already entered vehicle identification number is stamped in line 2.

Body
Fig. 74: Identifying Display

Start stamping operation with pushbutton (2).

After the stamping operation, if necessary adapt ENGINE COMPARTMENT LID SEAL LOCATOR of second vehicle identification number.

Body
Fig. 75: Stamping Vehicle Identification Number

Following layout functions are available:

VEHICLE IDENTIFICATION NUMBER CHART

Body

Body

    READ NEXT:

     Straightening Aluminium Components In Structure

    Reshaping or heating extruded sections and cast parts is not permitted! Failure to comply with this requirement would have the following results: In the case of reshaping, weld seams (E52) or

     Use Of Materials In Outer Skin

    The following illustration is a schematic representation of all the body variants. Apply this illustration to the relevant vehicle. Fig. 76: Identifying Vehicle Components All components not listed

     Welding In Reinforcement Plate (Steel Plate)

    In the case of a partial replacement piece, a body component is cut at a point described in the repair instructions. A reinforcement plate is welded in to ensure sufficient strength. Follow notes f

    SEE MORE:

     Sockets

    Concept The lighter socket can be used as a socket for electrical equipment when standby and driveready state are switched on. General information The total load of all sockets must not exceed 140 watts at 12 volts. Do not damage the socket by using non-compatible connectors. Safety information Wa

     Diagnosis For Condition Based Service

    NOTE: Red symbol for pre-delivery check The vehicle is coded at the end of the assembly line so that the red symbol for the pre-delivery check is shown in the Next Service display (same symbol as vehicle check). The symbol is a reminder to the Service staff that the pre-delivery check has not yet

    © 2019-2025 Copyright www.bmw7g11.com