BMW 7 Series: Removing And Installing/Replacing Front Left Or Right Seat Belt
Necessary preliminary tasks
- Remove trim panels for door pillar.
Installation
- Microencapsulated screws (Loctite) must be replaced and may not be reused
- Screw connection must be completed within 20 minutes (start of curing)
- Microencapsulated screws must not be retightened
- Clean thread of nut beforehand in event of repeated use
Version with anchor fitting tensioner:
Necessary preliminary tasks
- Remove OUTER COVER
Release screw (1).
Tightening torque 72 11 07AZ.
Remove lock washer.
Pull belt strap (2) out of end fitting pretensioner.
.png)
Fig. 6: Pulling Belt Strap Out Of End Fitting Pretensioner
Version without anchor fitting tensioner:
Move front seat upwards.
Release screw (1) on front seat.
Installation: Replace screw.
Tightening torque 72 11 02AZ.
Feed out belt anchor fitting (2).
.png)
Fig. 7: Identifying Front Seat Screw
Unfasten screws (2).
Tightening torque 72 11 04AZ.
Remove seat belt guide loop.
Release screws (1).
Installation: Replace screws (1).
Remove belt deflector.
Tightening torque 72 11 05AZ.
.png)
Fig. 8: Identifying Belt Deflector Screw
Release screw (1).
Installation: Replace screw.
Tightening torque 72 11 01AZ.
Unlock automatic reel (2) and remove from B-pillar.
Installation: Automatic reel is encoded against incorrect installation (3).
.png)
Fig. 9: Identifying Automatic Reel With Screw
Version with electric motor retractor
Release screws (1).
Installation: Replace screws.
Tightening torque 72 11 01AZ.
Unlock automatic reel (2) and remove from B-pillar.
Installation: Retractor mechanism is encoded against incorrect assembly.
.png)
Fig. 10: Identifying Automatic Reel With Screw
Unfasten plug connection (1) and disconnect.
Remove complete seat belt.
.png)
Fig. 11: Identifying Seat Belt Plug Connection
Installation
Carry out FUNCTION CHECK.
REMOVING AND INSTALLING/REPLACING FRONT LOWER BELT FITTING (BELT TENSIONER), DRIVER'S SEAT
Necessary preliminary tasks
- Remove FRONT SEAT, DRIVER'S SIDE
Installation
- Microencapsulated screws (Loctite) must be replaced and may not be reused
- Screw connection must be completed within 20 minutes (start of curing)
- Microencapsulated screws must not be retightened
- Clean thread of nut beforehand in event of repeated use
UNLOCK AND DISCONNECT plug connections (1).
.png)
Fig. 12: Identifying Driver's Seat Plug Connections
Release screw (1).
Installation: Replace screw (1).
Tightening torque 72 11 03AZ.
Remove seat belt tensioner.
Installation:
Belt tensioner is coded against incorrect installation.
.png)
Fig. 13: Identifying Seat Belt Tensioner Screw
READ NEXT:
Removing And Installing/Replacing Front Lower Strap Fitting (Belt
Tensioner), Front Passenger Seat
Necessary preliminary work
Remove FRONT PASSENGER SEAT
Installation note:
Microencapsulated screws (Loctite) must be replaced and may not be
reused
Screw connection must be completed within 20
Removing And Installing/Replacing Rear Left Or Right Lower Belt
Fitting (MFS)
Necessary preliminary tasks
Remove rear seat.
Unfasten plug connection (1) and disconnect.
Release sleeve nut (2).
Tightening torque 72 11 27AZ.
Remove lower belt fitting.
Installation:
Lower
SEE MORE:
With Parking Assistant
Plus: Surround View- Panorama View
Concept
The system provides an early look at cross traffic
at blind driveways and intersections.
General information
Road users concealed by obstacles to the left
and right of the vehicle can only be detected relatively
late from the driver's seat. The cameras in
the front and rear capture the sid
System Components
Spare Parts of Slide/tilt Sunroof
The slide/tilt sunroof in the F01/F02 consists The following table lists the
most important of mechanical and electrical components.
COMPONENTS DESCRIPTION CHART
Electrical Components
The following graphic shows all the electrical components of the slide/tilt
sun
