BMW 7 Series: Distance Systems, Cruise Control And Park Distance Control
DISTANCE SYSTEMS, CRUISE CONTROL
OPPS DEVICE
OPPS device MW
Note: (OPS package) (complete set)
Consisting of:
1 = 0495304 OPS device
NOTE: To order the OPS devices, please contact the appropriate SIEMENS hotline.
2 = 0495305 Cable
NOTE: (OBD cable, incl. CAN line)
3 = 0495306 Adapter cable
NOTE: (LAN adapter cable) To order the LAN adapter cable, please contact the appropriate SIEMENS hotline.
NOTE: Specify the LAN adapter cable model (crossed or uncrossed).
PARK DISTANCE CONTROL
REMOVING AND INSTALLING/RENEWING A CENTER FRONT LEFT ULTRASONIC SENSOR
Necessary preliminary work
- Remove MIDDLE LEFT OR RIGHT RADIATOR GRILLE
Release retaining tabs (2).
Press ultrasonic sensor from outside towards inside and remove.
Unfasten plug connection (2) and disconnect.
Installation note: Retaining tabs (2) must not be damaged! Make sure ultrasonic sensor is securely seated.
.png)
Fig. 1: Identifying Plug Connection With Tabs
Installation note: Make sure rubber ring (1) is correctly seated on ultrasonic sensor (2).
.png)
Fig. 2: Identifying Rubber Ring And Ultrasonic Transducer
REMOVING AND INSTALLING/RENEWING A CENTER FRONT RIGHT ULTRASONIC SENSOR
The following repair work is described in:
REMOVING AND INSTALLING/RENEWING A CENTRE FRONT LEFT ULTRASONIC SENSOR
REMOVING AND INSTALLING/REPLACING A FRONT CENTER ULTRASONIC SENSOR
Necessary preliminary tasks
- Remove MIDDLE LEFT OR RIGHT RADIATOR GRILLE
Release retaining tabs (2).
Press ultrasonic sensor from outside towards inside and remove.
Unfasten plug connection (2) and disconnect.
.png)
Fig. 3: Identifying Plug Connection With Tabs
Installation: Retaining tabs (2) must not be damaged! Make sure ultrasonic sensor is securely seated.
Installation
Make sure rubber ring (1) is correctly seated on ultrasonic sensor (2)!
.png)
Fig. 4: Identifying Rubber Ring And Ultrasonic Transducer
REMOVING AND INSTALLING/REPLACING A FRONT LEFT ULTRASONIC TRANSDUCER
Release the expanding rivet at marked points.
Fold wheel arch panel (1) to one side.
.png)
Fig. 5: Locating Wheel Arch Panel
Unfasten plug connection (1) and disconnect.
Unclip ultrasonic transducer from retaining tabs (2).
.png)
Fig. 6: Identifying Plug Connection With Tabs
Installation note: Retaining tabs (2) must not be damaged! Make sure ultrasonic sensor is securely seated.
Installation note: Make sure rubber ring (1) is correctly seated on ultrasonic sensor (2).
.png)
Fig. 7: Identifying Rubber Ring And Ultrasonic Transducer
REMOVING AND INSTALLING/REPLACING A FRONT RIGHT ULTRASONIC SENSOR
The following procedure is identical to:
- Removing and installing/renewing A FRONT LEFT ULTRASONIC SENSOR
REMOVING AND INSTALLING/REPLACING A REAR ULTRASONIC TRANSDUCER
Necessary preliminary work
- Remove REAR BUMPER TRIM
Unfasten plug connection (1) and disconnect. Unlock latch mechanisms (2) and pull ultrasonic transducer (3) out of bracket.
Installation note: Retaining tabs (2) must not be damaged! Make sure ultrasonic sensor is securely seated.
.png)
Fig. 8: Identifying Plug Connection, Tabs And Ultrasonic Transducer
Installation note: Make sure rubber ring (1) is correctly seated on ultrasonic sensor (2).
.png)
Fig. 9: Identifying Rubber Ring And Ultrasonic Transducer
READ NEXT:
Adaptive Cruise Control
ADJUSTING ACC SENSOR (FRR SENSOR)
NOTE: This document applies to the entire F series with the new ACC sensor
(FRR -
Full Range Radar).
Special tool required:
Holder 36 1 100
Active Cruise Control
Lane Change Warning
REMOVING AND INSTALLING/REPLACING SENSOR FOR LANE CHANGE WARNING
(HC2 SENSOR) ON LEFT OR RIGHT
Necessary preliminary work
Remove REAR BUMPER TRIM
Disconnect plug connection (1).
Unfasten screws (2
Parking Assist System
REMOVING AND INSTALLING / REPLACING PARK ASSIST CONTROL UNIT
Necessary preliminary work:
Remove RIGHT LUGGAGE COMPARTMENT WHEEL ARCH PANEL.
Unlock plug connection (1) and disconnect.
Pull out par
SEE MORE:
Zero Position Sensor
The zero position of the swivel module with respect to the zero position
sensor is detected by a 1/0 edge when
swivelling from the direction of the off position in the direction of the
optical axis. The swivel module is
repeatedly calibrated during operation based on this "soft" reference point.
Wiper system
General information
Do not use the wipers if the windshield is dry, as
this may damage the wiper blades or cause them
to become worn more quickly.
Safety information
Warning
If the wipers start moving in the folded away
state, body parts can be jammed or damage
may occur to parts of the vehicle. Th
