BMW 7 Owners & Service Manuals
BMW 7 Series (F01/F02) 2008-2015 Service Manual / Steering And Wheel Alignment / Pump And Oil Supply / Removing And Installing Power Steering Pump For Power Steering Gear With Active Front Steering (N63)

BMW 7 Series: Removing And Installing Power Steering Pump For Power Steering Gear With Active Front Steering (N63)

WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin!

IMPORTANT: Adhere to the utmost cleanliness. Do not allow any dirt to enter the hydraulic system.

Seal off hydraulic lines with plugs.

Necessary preliminary tasks

  • Draw off and dispose of hydraulic fluid from fluid reservoir
  • Remove BELT PULLEY
  • Remove FAN COWL
  • Remove front assembly underside protection.

Release hose clamp (1) and detach suction line from power steering pump.

Installation: Replace hose clamp.

Make sure hydraulic lines are laid without tension and with sufficient spacing to adjoining components.

Align suction line by way of marking (2) to power steering pump connection marking.

Pump And Oil Supply
Fig. 120: Identifying Power Steering Pump Connection Marking With Hose Clamp

Release screw (1).

Tightening torque 32 41 10AZ.

Release screw (2) and detach pressure line from power steering pump.

Tightening torque 32 41 18AZ.

Unlock plug connection (3) on back of power steering pump and disconnect.

Installation: Make sure hydraulic lines are laid without tension and with sufficient spacing to adjoining components.

Pump And Oil Supply
Fig. 121: Identifying Power Steering Pump Pressure Line Screws And Plug Connection

Align suction line by way of marking to connection on power steering pump.

Release screws (1, 2) and remove power steering pump.

Tightening torque 32 41 9AZ.

Installation: Replace screws.

Make sure screws are installed in correct positions.

  • Screw (1) M10x110
  • Screw (2) M10x130

Pump And Oil Supply
Fig. 122: Identifying Power Steering Pump Screws

After installation

  • Fill and bleed HYDRAULIC SYSTEM
  • Check pipe connections for leaks

    READ NEXT:

     Removing And Installing Vane Pump For Hydraulic Steering

    NOTE: See procedure for POWER STEERING PUMP FOR POWER STEERING GEAR WITH ACTIVE FRONT STEERING (N63) or POWER STEERING PUMP FOR HYDRAULIC STEERING GEAR WITH DYNAMIC DRIVE (N63). REMOVING AND INSTALLIN

     Removing And Installing/Renewing Dynamic Drive In The Wheel Arch

    Notes WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin! IMPORTANT: Adhere to the utmost cleanliness. Do not allow

     Removing And Installing/Replacing Return Line For Power Steering With ARS (N63)

    Notes WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin! IMPORTANT: Adhere to the utmost cleanliness. Do not allow

    SEE MORE:

     Information On Using Cleaning Agent/Paints (Personal Protection Equipment)

    WARNING: Use of cleaning agents/paints not compliant with instructions can cause serious injuries or burns! Handling cleaning agents/paints can trigger allergic skin and respiratory reactions! IMPORTANT: Observe following instructions: Store cleaning agents/paints only in a secure cabinet. Keep

     Bleeding Power Steering (Version With Dynamic Drive)

    WARNING: DANGER OF POISONING if oil is ingested/absorbed through the skin! RISK OF INJURY if oil comes into contact with eyes and skin! IMPORTANT: Adhere to the utmost cleanliness. Do not allow any dirt to enter the hydraulic system. Using contaminated equipment to add fluid may introduce dirt pa

    © 2019-2024 Copyright www.bmw7g11.com